Hisky HCP100S 6CH 3 Axis Gyro Dual Brushless RC Heli+HT8 Adapter
Note: HCP100S has been improved now.
Add to Cart
1. Compatible with DSMX and DSM2 satellite receivers. included AR6210,AR6200,AR8000(11ms or 22ms)
2. Improves the servo movement. (Optimizes the binding procedure to avoid unexpected servo jamming, and larger the servo moving place to avoid unexpected servo lagging.
3. Improves performance and stability.
Hisky HCP100S 6CH 3 Axis Gyro Dual Brushless RC Helicopter With Third Generation HT8 Adapter
Three Methods binds with Hisky HCP100S :
1.Transmitter:Hisky H-6(HCP80 V2 Transmitter) and X-6S (new version,not SKU051544) can bind with Hisky HCP100S BNF.
2.Compatible with the Hisky HT-8 module(the second SKU059200 or third generation) and your transmitter has simulated function,it can also bind with this item.
3.Compatible with DSMX satellite receiver(Not included), can be connected to Spektrum Transmitter(following figures).
Main Rotor Dia.: 113mm
Tail Rotor Dia.: 38.4mm
Rotating propeller Dia.: 249mm
Battery: 7.4V 450mAh 25C
Main Motor: KV8000 Outrunner
Tail Motor: KV8200 Outrunner
Steel main shaft
Direct-drive tail rotor
Dual brushless ESC
7.4V 450mAh 25C Lipo Battery
Patented linear servo technology
Fully-assembled and flight tested
8200KV brushless tail outrunner motor
Compatible with the Hisky HT-8 module
8000KV brushless main outrunner motor
3 axis stabilization with pirouette compensation
Compatible with DSMX and DSM2 satellite receivers.(Not included)
HT8 Radio Adapter:(Third Generation)
Remote Control,Shatter Resistant
State of Assembly: Ready-to-Go
Power Source: Electric
Battery: 3.7V 150mAh 15C Li-Poly
Flight time: 4 to 5 minutes
First put the internal power supply switch to OFF position,no LED lights on RF Module bright this time,then connect RF Module to a computer (or the other power supplier equipment)using USB wire,this time,Signal indicator light starts to flash and Mode indicator light shows charging status:red means charging,turning to green means charging is over.
Nomal use operation:
1.supplying power of radio itself (eg:JR/Futaba) the HT-8 internal power supply swith to OFF stare.Properly connected HT-8's signal cables .(JR signal cable connecting the remote control DSC interface,and power cable to cnnnect to DC charging port)(Futaba's connection is a combination of signal cable and power cable to connect simulator interface).
2.If no power from radio,switch the HT-8 internal power supply to on state.Properly connected HT-8 and remote control of the DSC interface.
3.Under normal circumstances the HT-8 light is green,when red check the signal cable if is normal,as well as check the remote control to set the modulation mode to PPM format,Set the types of remote control through switch the button of high-frequency head,the status indicator of remote control through switch the button of high-frequency head,the status indicator (Model),futaba(green) JR(red).WAKERA (not light).
1.There is one 3.7V Li-po Battery sealed in the RF Module. If the redio controller you use can supply the power to the RF Module, please turn off the sealed battery to off status.
2.Please pay attention to the battery power when you use sealed battery of RF Module, if the green light is flashing, please stop to play and charge the battery.
HT8 Radio ADAPTER Parameter:
Sealed battery specification:3.7V Li-Po battery 120mAh
Operating voltage:5-12V. DC
Operating Frequency:2402 MHZ-2477 MHZ
Spread Spectrum mode:FHSS
Number of frequency channels: 20
Hoping Rate: 240 Jump/s
The English manual Click Here
1 x Hisky HCP100S RC Helicopter(Body)
1 x 7.4V 450mAh 25C Lipo Battery
1 x Main Blade(1 set)
1 x Tail Blade
1 x Manual
1 x HiSKY HT8 Adapter Module(Third Generation)